Networking & Security
1
Posts
1
Users
0
Likes
266
Views
Topic starter
- Can router on different subnet become BGP neighbour?
- What is the difference between eBGP multihop and TTL security?
- Which protocol and the port number does BGP use for neighborship?
- What is the use of BGP best path community ignore command?
- How do I configure BGP with the use of a loopback address?
- What is the order of preference of attributes when applied to one neighbour in BGP?
- What does a next-hop of 0.0.0.0 mean in the show IP BGP command output?
- What are the well-known communities of the BGP community attribute?
- How does BGP behave differently with auto-summary enabled or disabled?
- What formats can I use to configure the BGP community attribute?
- When and how should I reset a BGP session?
- Is there any special configuration needed on PIX/ASA to allow BGP sessions through it?
- What is an autonomous system number (ASN) and how do I obtain one?
- What is the BGP path selection criteria?
- What is the difference between always-compare-med and deterministic-med?
- Do internal BGP (iBGP) sessions modify the next-hop?
- Do external BGP (eBGP) sessions modify the next-hop?
- Do external BGP (eBGP) sessions between confederations modify the next-hop?
- In external BGP (eBGP) sessions, which IP address is sent as the next hop?
- Does the route reflector change the next-hop attribute of a reflected prefix?
- How can I announce a prefix conditionally to one ISP only when I lose the connection to my primary ISP?
- How can I configure BGP to provide load sharing and redundancy in my network?
- How much memory should I have in my router to receive the complete BGP routing table from my ISP?
- What are the benefits of configuring BGP peer groups?
- Why do I see the same route twice from the same peer in BGP?
- What is synchronization, and how does it influence BGP routes installed in the IP routing table?
- How do I know which Cisco IOS software release supports a particular BGP feature?
- How can I set the Multi Exit Discriminator (MED) value on prefixes advertised to external BGP (eBGP) neighbours to match the Interior Gateway Protocol (IGP) next hop metric?
- What is the default BGP Connect Retry timer, and is it possible to tune the BGP Connect Retry timer?
- How can I filter all IP routes advertised to a BGP neighbour except the default route 0.0.0.0/0?
- Is it possible to track an interface and change the route availability?
- How does IP RIB Update allocate memory?
- What is the command to see IPv6 BGP neighbours?
- In regards to the removal of the static route “ip route 10.10.0.0 255.255.0.0 Null0”, does no auto-summary in BGP cause all subnets of 10.10.0.0 to be advertised?
- Why are there no statistic results when I use the debug bfd events and debug bfd packets commands?
- Can I run two BGP process on a single router?
- Difference between hard reset and soft reset in BGP?
- What are different BGP message types
- What are various BGP states?
- Which command is used to disable BGP neighborship?
- What are the values of keepalive and Dead timers in BGP?
- How many public and private AS numbers are there?
- BGP Route selection criteria?
- Does the router have to be restarted after a new BGP Neighbor Maximum Prefix is configured?
- Is there a command to check the advertised routes along with the prepend of the AS-paths?
- How does neighbour soft-reconfiguration inbound command function?
- What is the difference between when a route is injected in BGP via redistributing command or a network command?
- How do I verify Layer 4 forwarding summary information?
- What are IGPs and EGPs and why are they different?
- Why is there a problem with iBGP in large networks? How can this problem be solved?
- Name BGP path attributes to control incoming and outgoing traffic
- My BGP is showing 0.0.0.0 as router-id; what could be the possible reason?
- If my BGP neighbour is stuck in an idle or active state, what should I do?
- Explain BGP recursive lookup and site of origin (SoO).
- What do you understand by BGP split-horizon rule?
- Describe BGP communities. Name well-known communities.
- Can I use BGP instead of any IGP?
- Types of a BGP routing table?
- What is route reflector and why it is required?
- What is no-synchronization rule?
- What are Default BGP timers?
- In Multihoming scenario, if the primary link gets fail, after how long traffic will be shifted to the secondary link?
- BGP Graceful Restart, NSR and NSF?
- How to use BGP as PE-CE backdoor link?
- What is the advantage of using BGP AS Prepend?
- What is cluster id in BGP?
- What is the meaning of update-source loopback?
- Can we use local preference outside the autonomous system?
- What is confederation?
- What is Route Reflector in BGP? Why is it required?
- What will the BGP first check to see if a prefix is accessible?
- What are the two methods for reducing the number of IBGP connection in a network?
- What makes a neighbour internal BGP (iBGP)?
- What the command “neighbour update-source” do?
- Explain the term RIB in BGP?
- Two BGP peers connected through a routed firewall are unable to establish a peering relationship. What could be the most likely cause?
- What is the order of preference of attributes (route-map, filter-list,prefix-list, distribute-list ) when some or all are applied to one neighbour in BGP? Kindly share for inbound updates?
- What is the order of preference of attributes (route-map, filter-list,prefix-list, distribute-list ) when some or all are applied to one neighbour in BGP? Kindly share for inbound updates?
- How can I verify if a BGP router announces its BGP networks and propagates them?
- What is the difference between always-compare-med and deterministic-med?
- Does the route reflector change the next-hop attribute of a reflected prefix?
- How can I announce a prefix conditionally to one ISP only when I lose the connection to my primary ISP?
- How much of minimal RAM is required to learn complete BGP routing table from one BGP peer?
- What are the benefits of configuring BGP peer groups?
- What is the default BGP ConnectRetry timer
- What does r RIB-Failure mean in the show ip bgp command output?
- How can I filter all IP routes advertised to a BGP neighbour except the default route 0.0.0.0/0?
- In the global routing table, can the same AS number shows up more than once in a path?
- What is the cost of external and internal BGP routes?
- Which parameters and attributes have to be equal before MED is compared to select the best path?
- How do we enable community propagation?
- What is the purpose of route dampening?
- In general which routes will affect by route dampening? eBGP or iBGP?
- What is the default value of MED?
Posted : 05/03/2023 7:08 pm
